AMT Datasouth 7200 Guia do Utilizador

ATB PrinterUser's Guide7200Part No. 111017 Rev. D

Operation Manualvii7200INTRODUCTIONAvailable TypesThe Sigma Data — 7200 ATB printer is classified into 2 types, i.e., Type B and Type D. Referto the

Operation Manualviii7200NOTES (page is intentionally blank)

1-1Operation Manual7200BEFORE USING THE S72001. Before Using the ATB Printer

1-2 Operation Manual7200Operation ManualAC Power CableATB PrinterKeys1.1 Checking the PackageThe ATB printer and accessories are packed in the same bo

1-3Operation Manual7200BEFORE USING THE S7200N — BIN 3K — Power switchJ — Interface connector(Downline)B — Cover lockL — Power connectorM — Interface

1-4 Operation Manual72001.2.2 FunctionsNo. Names FunctionsA Operator panel Houses the LEDs and keypad needed to operatethe ATB printer.B Cover lock Lo

1-5Operation Manual7200BEFORE USING THE S72001.2.3 Operator PanelOperator Panel LayoutLEDsLCD16 columns by 2 rowsKeysééççêêERRORERRORONLINEONLINE DATA

1-6 Operation Manual7200Key FunctionsEach key has two different functions for different operating modes.FunctionskeyFunction indicated at the top Ena

1-7Operation Manual7200BEFORE USING THE S7200keykeykeyTESTIn OFFLINE (local) mode, pressing this key sets the ATB printerto TEST mode (maintenance mod

1-8 Operation Manual7200NOTES (page is intentionally blank)

Operation Manual7200Introduction... i1. Before Using the ATB Printer ...

7200OPERATION2-1Operation Manual2. Operation

72002-2Operation Manual2.1 Connecting the ATB PrinterThis section explains how to connect the ATB printer to the power supply and the terminal.2.1.1 C

7200OPERATION2-3Operation Manual2.1.2 Connecting the TerminalBefore connecting the printer to a terminal, do the following:HOSTA. Ensure that both the

72002-4Operation Manual2.2 Turning the Power On and OffAfter the ATB printer has been successfully installed and connected, turn on the power.Note!Tur

7200OPERATION2-5Operation Manual2.3 Loading the DocumentsFalling covers maycause injury. Do nottake your hands offcovers when open-ing and/or closingt

72002-6Operation ManualMagstripe(When loading a box)MagstripeFront endBIN 2BIN 1Document OrientationSide cover (top right)D. Slowly open the second si

7200OPERATION2-7Operation ManualBIN 2BIN 2VisualinspectionwindowBIN 1BIN 1G. Feed the document into the rollers. Turnthe knob to feed the front end of

72002-8Operation ManualH. Close the side cover (top right).I. Set the key to the OPEN position, andclose the side cover (bottom right).J. Lock the sid

7200OPERATION2-9Operation ManualDocumentsSet the documents as follows:(Documents in a box)PrinterLocation of documentsMagstripeFront endDocumentsFront

72002-10Operation ManualFalling covers maycause injury.Do not take yourhands off coverswhen opening and/or closing them.CAUTIONSide cover(bottom right

Operation Manual7200(Page is intentionally blank)

7200OPERATION2-11Operation ManualMagstripe face downBIN 3 slotVisualinspectionwindowH. Close the side cover (top right).G. Feed the document. Turn the

72002-12Operation ManualI. Set the key to the OPEN position, andclose the side cover (bottom right).J. Lock the side cover by gently pushing theside c

7200OPERATION2-13Operation Manual2.5 Loading Documents into the InserterWhile the ATB printer is on, you can use the inserter to read and/or print a d

72002-14Operation Manual2.6 Installing the Transfer Ribbon (TT — Type D Only)Install the transfer ribbon according to the procedure below. The followi

7200OPERATION2-15Operation ManualFalling covers maycause injury.Do not take yourhands off coverswhen opening and/or closing them.CAUTIONSide cover(bot

72002-16Operation ManualTransfer ribbon winding directionLockG. Remove the ribbon loader. Squeeze thelock with your fingers to remove theloader.H. Tur

7200OPERATION2-17Operation ManualK. Lock the side cover by gently pushing theside cover and turning the keycounter-clockwise to the LOCK position.Remo

72002-18Operation Manual2.7 Changing Transfer Ribbons (TT — Type D Only)When the transfer ribbon needs replacement, the LCD panel displays a message.L

7200OPERATION2-19Operation ManualPivotsD. Pinch both blue pivots to unlock and takeout the used transfer ribbon.Note!It is normal for some unused tran

72002-20Operation ManualNOTES (page is intentionally blank)

Operation Manuali7200INTRODUCTIONNOTICEThis equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to Par

7200DAILY MAINTENANCE3-1Operation Manual3. Daily Maintenance

72003-2Operation Manual3.1 Cleaning the ATB PrinterThis section explains the ATB printer components that need regular cleaning.3.1.1 Cleaning the Prin

7200DAILY MAINTENANCE3-3Operation Manual3.1.2 Cleaning the Magnetic HeadMagnetic particles, paper particles, or dust sticking to the magnetic head may

72003-4Operation ManualC. Insert the cleaning card.• Insert the cleaning card with theinstruction label on the card facingupward.• The LCD panel disp

7200DAILY MAINTENANCE3-5Operation ManualAvoid fire whenusing isopropylalcohol to reducethe risk of burning.CAUTION1. Moisten a cotton swab with isopro

72003-6Operation Manual3.1.4 Cleaning a Platen RollerClean the platen roller when replenishing a bin with documents. Use a cotton swab moist-ened with

7200DAILY MAINTENANCE3-7Operation Manual3.1.5 Cleaning a Carrier RollerPaper dust and other dirt clinging to a carrier roller can cause a paper jam or

72003-8Operation ManualHead position of thecleaning sheet Bin and Cutter Blocks1. Uniformly apply a small amount ofisopropyl alcohol to the long, thin

7200DAILY MAINTENANCE3-9Operation Manual3.1.6 Removing Paper DustPaper dust should be removed from the dust tray periodically.DusttrayKnobAlthough the

72003-10Operation ManualNOTES (page is intentionally blank)

Operation Manualii7200Product SafetyThis manual uses a variety of terms and symbols to ensure the safe operation of the product,help prevent hazards t

7200TROUBLESHOOTING4-1Operation Manual4. Troubleshooting

72004-2Operation Manual9.1 Paper JamIn the event of a coupon jam, a buzzer sounds and the LCD panel displays a messageindicating the location of the j

7200TROUBLESHOOTING4-3Operation Manual4.1.3 Removing the jammed couponTo remove the jammed coupon, check the location of the jam and follow the steps

72004-4Operation ManualC. Remove the jammed coupon from theappropriate bin.1. Use the knob where the jamoccurred:BIN 1 — red knobBIN 2 — yellow knobBI

7200TROUBLESHOOTING4-5Operation ManualD. Remove the jammed coupon (cutterblock)After the jammed coupon has beencut:1. Locate the blue knob labeled&quo

72004-6Operation ManualIf the jammed coupon has NOT beencut:1. Use the knob for the appropriate binAND the feed knob.2. Turn both knobs clockwisesimul

7200TROUBLESHOOTING4-7Operation Manual3. Pull the jammed coupon out of theinput slot and remove the damagedcoupon.E. Remove the jammed coupon from the

72004-8Operation ManualPrinting block andoutput stacker blockFeed knobF. Remove the jammed coupon fromthe printing block and outputstacker.1. Locate t

7200TROUBLESHOOTING4-9Operation ManualWhen the jammed coupon is notcaught by the rollers shaded in thefigure:1. Locate the blue feed knob labeled"

72004-10Operation ManualBladeInserterG. Remove the jammed coupon. (Inserter)1. Locate the blue feed knob labeled"Forward."(The rear end of t

Operation Manualiii7200INTRODUCTIONSafety ConsiderationsREAD THIS PAGE BEFORE INSTALLING OR USING THIS PRODUCT!n Do not remove the cover or attempt an

7200TROUBLESHOOTING4-11Operation ManualFalling covers maycause injury.Do not take yourhands off coverswhen opening and/or closing them.CAUTIONJ. Lock

72004-12Operation Manual4.2 Error MessagesWhen an error has occurred in the ATB printer, an error message is displayed on the LCDpanel. The error mess

7200TROUBLESHOOTING4-13Operation ManualError Message Error State Recovery ProcedureOUT OFREQUESTED PAPERThe requested document has ended. Install the

72004-14Operation ManualThe following error messages are reference data. They concern a service engineer.Error Message Error State Recovery ProcedureI

7200TROUBLESHOOTING4-15Operation ManualError Message Error State Recovery ProcedureSYSTEM ERROR:PRINT POSITIONAn error has occurred during the print h

72004-16Operation ManualNOTES (page is intentionally blank)

7200APPENDIXAPPENDIX-1Operation ManualAppendix 1: SpecificationsA.1.1 Document Carrier StructureMagnetic blockCutter blockPrinting blockBIN 2 BIN 1BIN

7200APPENDIX-2Operation ManualA.1.2 CoversOpen (swing down) the bottom right side cover first, then open (swing up) the top right sidecover. You can i

7200APPENDIXAPPENDIX-3Operation ManualTemperature and HumidityMake sure that the following temperature and humidity conditions are met :• Ambient temp

7200APPENDIX-4Operation Manual(2) Document specifications(3) Detection(4) Documents setA.1.5 Encoding Specifications(1) Magnetic encode method(2) Trac

Operation Manualiv7200Caution LabelThis product comes with a caution label attached as described below.CAUTIONCaution LabelFalling covers maycause inj

7200APPENDIXAPPENDIX-5Operation ManualA.1.7 Inserter(1) Document feeding direction(2) Shutter(3) Non-standard documents inserted(4) Document feeding(5

7200APPENDIX-6Operation ManualStoringTransfer RibbonsTo store transfer ribbons, note the following:• Do not open the package if the ribbon is to be st

AMT Datasouth Corp.Corporate Headquarters4765 Calle QuetzalCamarillo, CA 93012(805) 388-5799 PH(805) 484-5282 FXCharlotte Operation4216 Stuart Andrew

Operation Manualv7200INTRODUCTIONLeftRightLeftRightFrontTopBackinches (millimeters)9.8 in (250mm)15 in (380mm) 9.8 in (250mm) 5.9 in (150mm)Space Requ

Operation Manualvi7200Temperature and HumidityMake sure that the following temperature and humidity conditions are met :• Ambient temperature: 41 to 1