AMT Datasouth Fastmark M5 Plus Series Guia do Utilizador Página 1

Document #120522 Rev-A i Fastmark M5 Plus Series Thermal Transfer Barcode Printer User’s Guide

Document #120522 Rev-A 7 Make sure the printer top cover is engaged properly at both sides prior to powering up the printer. Please follow the steps

Document #120522 Rev-A 8 Fig. 5 Ribbon installation (II) 3.4 Loading Media Stock 1. Insert spindle into a media roll (If your media core is 1

Document #120522 Rev-A 9 2. Open the printer’s top cover by releasing the green levers located on each side of the printer and lifting the top cover.

Document #120522 Rev-A 10 Fig. 8 Media installation (II) 3.5 External Media Roll Mount Installation (Option) 1. Attach an external media roll moun

Document #120522 Rev-A 11 Fig. 10 External roll mount media installation (I) 5. Continue feeding the media through the interna

Document #120522 Rev-A 12 3.6 Peel-off Module Installation (Option) 1. Open the top cover and remove the front panel from the printer.

Document #120522 Rev-A 13 4. Turn over the printer. Remove two screws located near the top cover hinge, and remove one screw at memory card cover. 5

Document #120522 Rev-A 14 Peel Off Assembly TabInner Hinge Holes 7. Insert the peel-off assembly tabs into the lower inner cover hinge holes until

Document #120522 Rev-A 15 Peel-off panel Backing paper Opening 3.6.1 Loading Labels into Peel-off Module Note: Both thermal paper and plain p

Document #120522 Rev-A 16 5. Feed the label, printing side facing up, through the paper guides and place it on top of the platen. 6. Thread the lab

Document #120522 Rev-A ii COMPLIANCES... III 1. Introduct

Document #120522 Rev-A 17 3.7 Cutter Module Installation (Option) 1. Pull the top cover open levers to open the top cover. 2. Remove the front pane

Document #120522 Rev-A 18 5. Turn over the printer. Remove two screws located near the top cover hinge. 6. Remove the screw from the memory card

Document #120522 Rev-A 19 9. Assemble the lower inner cover back onto the lower cover. 10. Install the cutter into the slots of the printer inner co

Document #120522 Rev-A 20 Paper Guide Platen Cutter Fig. 27 Media installation in cutter mode 7. Close the top cover by lifting u

Document #120522 Rev-A 21 3.8 Diagnostic Tool The Diagnostic Utility is a toolbox that allows users to explore the printer's settings and status

Document #120522 Rev-A 22 3.8.2 Printer Function (Calibrate, Ethernet, RTC setup…) 1. Select the PC interface connected with bar code printer. 2. Cl

Document #120522 Rev-A 23 3.9 Install Memory Card 1. Turn the printer upside down. 2. Remove the screw that fixes the memory card cover. 3. Plug

Document #120522 Rev-A 24 4. Power on Utilities There are six power-on utilities to set up and test printer hardware. These utilities are activated b

Document #120522 Rev-A 25 4.2 Gap/Black Mark Calibration, Self-test and Dump Mode While calibrate the gap/black mark sensor, printer will measure the

Document #120522 Rev-A 26 Self-test Printer will print the printer configuration after gap/black mark sensor calibration. Self-test printout can be u

Document #120522 Rev-A iii Copyright Declaration Information in this manual is subject to change without notice and does not represent a commitment o

Document #120522 Rev-A 27 Dump mode The printer will enter dump mode after printing the printer configuration. In the dump mode, all characters will

Document #120522 Rev-A 28 4.3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults. The only

Document #120522 Rev-A 29 4.4 Black Mark Sensor Setting and Calibration Please follow the steps as below. 1. Turn off the power switch. 2. Hold on

Document #120522 Rev-A 30 3. Release the FEED button when LED becomes solid green.  The LED color will be changed in the following: Amber  red (

Document #120522 Rev-A 31 ethanol and a cotton swab, or lint-free cloth. Tear Bar/Peel Bar Use the lint-free cloth with 100% ethanol to wipe it. As n

Document #120522 Rev-A 32 and from the power supply to the printer power jack if they are connected securely. Solid Green ON The printer is ready t

Document #120522 Rev-A 33 The Ethernet IP, subnet mask, gateway is not configured properly. Configure the IP, subnet mask and gateway. Label or ribb

Document #120522 Rev-A 34 7. LED and Button Operation 7.1 LED LED Color Description Green/ Solid This illuminates that the power is on and the de

Document #120522 Rev-A 35 Ribbon Sensor and Gap/Black Mark Sensor Calibration 1. Turn off the power switch. 2. Hold on the button then turn on the

Document #120522 Rev-A 36 Printer Initialization 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Rel

Document #120522 Rev-A 1 1. Introduction Thank you for purchasing the AMT Datasouth M5 PLUS series Thermal Transfer and Direct Thermal Bar Code Printe

Document #120522 Rev-A 37 Skip AUTO.BAS 1. Turn off printer power. 2. Press the FEED button and then turn on power. 3. Release the FEED button when

Document #120522 Rev-A 38 Revise History Date Content Editor 9-19-08 Pre-Production Release J. Nolan

Document #120522 Rev-A 39 Corporate Headquarters Manufacturing/Service 803 Camarillo Springs Road, Suite-D 503

Document #120522 Rev-A 2 Optional Configurations  Peel off module assembly.  Guillotine cutter Full cut: Paper thickness: 0.06~ 0.19mm, 500,000

Document #120522 Rev-A 3 2.3 Printer Parts Fig. 1 Top front view Top Cover Open LeverLED Indicator Feed Button Printer Top Cov

Document #120522 Rev-A 4 3. Setup 3.1 Instructions to Top Cover Operation Please take care when opening or closing the printer’s top cover by carefull

Document #120522 Rev-A 5 Note: DO NOT place your hands or fingers between the top and lower cover while closing! Top cover is fully open and ready

Document #120522 Rev-A 6 3.2 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect t